Nurse Call System - NCS Sleek

Models of Nurse Call System:




Working of NCS Sleek

             Works exactly like an Esteem version. Esteem Sleek is designed to make it very economical and thus enable small Hospitals or Nursing Homes to equipped with the most needed Nurse Call System to take good care of the patients.
            The electronics is optimised to cater to only a maximum of 8 beds so that it becomes very much affordable even for small Nursing Homes.
            Esteem Sleek NS Display draws the power from centrally located Patient Interface Hub.


Product Features

  • Makes use of LCD module of 128 X 64 pixels to show Call originating room No.s.
  • Voice module with Standard voice ” Attention; Patient Calling ” instead of buzzer makes it distinguished.
  • Very low working voltage (12V) to ensure patients safety.
  • Additional feature of Long Pending Call alert is an incidental benefit.
  • Very simple design to make it easily installable and maintenance free.
  • Door indicator helps the nurse to locate the calling patient easily.
  • Once a call is initiated, it remains registered even if it is cleared inadvertently, until it is acknowledged.”s room.


NCS Specifications:

 

Modules:

NS Display (Sleek)

NS Display Sleek               Nurse Station Display (NS) is designed around a RISC based microcontroller to read three keys, to update information on 128 x 64 LCD display and to show a maximum of 8 bed/ Calling unit information assigned to various rooms or patients. An integrated voice module also is controlled based on the information received from the PIH8

Power Button: Pressing this for long time (approximately 3 sec) turns the device ON or OFF.

MUTE Button: It is for acknowledging a call from patient. It will make the flashing window steady and also silences the voice module until a call is cleared.

Test Button: On pressing the button it will flash all the windows and will announce ”Attention, Patient calling” to make sure that the device is working fine.

Patient Interface Hub (PIH8)

PIH             Allows for 8 calling units and 8 toilet calling units. Uses 2 pairs of wires to get interconnected with NS Display Sleek. It works on 230V AC power supply.


CALLING UNITS


Electronic Calling Unit (CU)

calling unit
            The unit is designed with soft touch key pad consisting of one key for call initiation and another for clearing the call which is required to be done by the nurse attending the patient.
            Additional push button switch is integrated to this unit by means of a coil cord to enable a patient to initiate a call from the bed itself.

Dual Calling Unit (DCU)

calling unit
            The unit is designed to provide the two different calls (eg: Doctor and Nurse).Two separate windows at Nurse Station can be allocated.
            Additional push button switch is integrated to this unit by means of a coil cord to enable a patient to initiate a call from the bed itself.

Pull cord Switch (for Toilets) (TCU)

Toilet Unit

            This is designed with Pull cord switch and LED Indicator. The pull cord switch toggles between 'ON' and 'OFF' whenever it is pulled thus facilitating initiation or clearing the CALL.


Door Indicator


Door indicator             These semi circular shaped indicators can be mounted on the wall near the patient's door so that , nurse walking through the corridor can see it from a distance.These are made of super bright LEDs to indicate patient's call pending which can be seen from the corridor itself.


Models of Nurse Call System:


Display Windows
  • LCD Display                          : 128 X 64 pixels
  • Dimension                            : 80W x 50H mm

Indicators         : Flashing 5mm LED to indicate NCS is active.
Power                : 230 V AC +/-10%,50Hz, 15 watts

Front Panel Buttons
  • ”MUTE” for silencing the voice
  • ”TEST” for testing all the windows and the voice module.
  • ”PWR” to turn ON/OFF the equipment

Cable Specifications
  • Standard                             : Belden #8795 equivalent
  • Thickness                           : 22AWG twisted pair Characteristic
  • Impedance (Zo)                 : 100 E
  • Distributed Capacitance : 15 pF/ft
  • Propagation Delay            : 1.3 nsec/ft
  • Conductor Resistance    : 0.027 Ohms/ft (90 Ohms/Km approx.)

Environmental Specifications:
  • Operating Temperature  : 0 to 50* C
  • Humidity                              : 95% at 40*C
  • Storage Temperature      : 0 to 70* C
  • Altitude                                : 10,000 ft

Dimension/Weight
  • NS-LCD display                    : 180W x 127H mm x 88D mm 750 gm (approx.)
  • Calling Unit                         : 93.5W x 90H mm 100 gm (approx.)
  • Door Indicator                   : 70W x 70H mm 150 gm (approx.)