Nurse Call System - Esteem

Models of Nurse Call System:


Working of NCS-Esteem

             By turning ON the switch on the calling unit an indicator gets lighted up confirming that your call is passed on, which in turn reaches the Controller/Display unit and flashes the room number of the patient on it. simultaneously, the Voice module in it announces the call which forces the nurse to give immediate attention.
            After noticing the call the nurse can silence the voice module by pressing the MUTE button on Controller/Display Unit which makes the flashing window steady but it will continue glowing unless it is cleared by the nurse from the patient”s room using the calling unit. If another patient raises a call, again the same procedure takes place independent of the preceding call.
            Thus NCS ensures a positive and immediate response from the nurse for the patient needs.

Product Features

  • Makes use of super bright LEDs to enhance the life of indicators and reduce power consumption.
  • Voice module with Standard voice ” Attention; Patient Calling ” instead of buzzer makes it distinguished.
  • Very low working voltage to ensure patients safety.
  • Very simple design to make it easily installable and maintenance free.
  • Door indicator helps the nurse to locate the calling patient easily.
  • Once turned On by the patient it will remain registered till the nurse attend the patient and clears the call from the patient”s room.
  • NCS is designed with static windows and one can insert a bromide film (or similar thing) with the required letters to identify the room.

 

NCS Specifications:

 

Modules:

NS-Display


esteem display               This is a Microcontroller based device placed in the nurse station with static windows which displays the room number of the calling patient and also it has a voice module to announce the call. There are three buttons on it,

Power Button: Pressing this for long time(approximately 3 sec) turns the device ON or OFF.

MUTE Button: It is for acknowledging a call from patient. It will make the flashing window steady and also silences the voice module until a call is cleared.

Test Button: On pressing the button it will flash all the windows and will announce ” Attention, Patient calling ” to make sure that the device is working fine.

Electronic Calling Unit


calling unit
            The unit is designed with soft touch key pad consisting of one key for call initiation and another for clearing call which is required to be done by the nurse attending to the patient.
            Additional push button switch is integrated to this unit by means of a coil cord to enable a patient to initiate a call from the bed itself.


Toilet Calling Unit


Toilet Unit

            Here call is originated by pulling the cord and can be cleared by pulling it again. The LED indicator lights up if call is active. This allows the patient to initiate a call from squatting positions itself.



Door Indicator


Door indicator             These semi circular shaped indicators can be mounted on the wall near the patient's door so that , nurse walking through the corridor can see it from a distance.These are made of super bright LEDs to indicate patient's call pending which can be seen from the corridor itself.




230V Interface Module


            The interface unit to convert existing wiring (laid to work with 230V AC Buzzer) to 12V DC operated ” NURSE CALL SYSTEM ”. This interface and Nurse Call System can replace the existing buzzer system instantly without any change in cabling but providing for patient safety which was absent earlier.

Models of Nurse Call System:



Display Windows
  • No. of Windows                   : Maximum 16
  • Dimension                            : 30Wx22H mm
  • Light Source                        : Super Bright LEDs

Indicators         : Flashing 5mm LED to indicate NCS is active.
Power                : 230 V AC +/-10%,50Hz, 15 watts

Front Panel Buttons
  • ”MUTE” for silencing the voice.
  • ”TEST” for testing all the windows and the voice module.
  • ”PWR” to turn ON/OFF the equipment.

Cable Specifications
  • Standard                             : Belden #8795 equivalent
  • Thickness                           : 22AWG twisted pair Characteristic
  • Impedance (Zo)                 : 100 E
  • Distributed Capacitance : 15 pF/ft
  • Propagation Delay            : 1.3 nsec/ft
  • Conductor Resistance    : 0.027 Ohms/ft (90 Ohms/Km approx.)

Environmental Specifications:
  • Operating Temperature  : 0 to 50* C
  • Humidity                              : 95% at 40*C
  • Storage Temperature      : 0 to 70* C
  • Altitude                                : 10,000 ft

Dimension/Weight
  • NS-display                    : 250W x 160H x 110D mm 2Kg (approx.)
  • Calling Unit                         : 93.5W x 90H mm 100 gm (approx.)
  • Door Indicator                   : 70W x 70H mm 150 gm (approx.)